0

Out of 0 Ratings

Owner's of the Chamberlain Intercom System NDIS gave it a score of 0 out of 5. Here's how the scores stacked up:
  • Reliability

    0 out of 5
  • Durability

    0 out of 5
  • Maintenance

    0 out of 5
  • Performance

    0 out of 5
  • Ease of Use

    0 out of 5
of 4
 
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the
battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
41B238 . . . . . . . . . . . . . . . . . . . . . . . . 12 Vdc 300mA Adapter
The Chamberlain Group, Inc. warrants to the fi rst retail purchaser of this
product that it is free from defect in materials and/or workmanship for a period
of 1 year from the date of purchase.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FOR TECHNICAL SUPPORT DIAL OUR TOLL
FREE NUMBER:
1-800-528-9131
www.chamberlain-DIY.com
© 2010, The Chamberlain Group Inc.
114A4096D All Rights Reserved
Troubleshooting
Warranty Accessories
Intercom beeps every ten minutes.
The battery is low in the intercom. Replace with AA Alkaline
batteries or operate it with DC Adapter (not provided). A 12 volt,
300mA DC Adapter may be used (center positive polarity on the
round plug).
Need to clear intercom’s memory.
Press and hold Learn button, an initial beep will be heard.
Continue to hold until a second beep is heard (about 6 seconds).
Ensure other intercoms are not activated during this time. Once
memory is clear the intercom can be programmed to a new
network.
Static and feedback is heard in intercom.
The intercoms are too close to each other. A cordless phone,
cell phone, or other radio devices can also cause static.
Intercom is sending audio while no buttons are pressed.
The sending intercom is set to Monitoring Mode or Voice
Activation Mode and will activate when sound is heard. It can be
taken out of Monitoring Mode by pressing the Talk button. It can
be taken out of Voice Activation Mode by setting Dipswitch #1 to
DOWN position. See Features.
Doorbell does not function.
Check batteries in doorbell. When you press the Call button you
should hear a tone. Ensure doorbell is connected to a network.
See Program Intercom to Doorbell.
The doorbell will not function when an intercom is in Monitor
Mode.
Doorbell is not getting expected transmission range.
Keep doorbell away from metal objects and electrical wiring.
Do not mount doorbell on a tree, masonry, or metal surface.
When used in buildings with stucco or cement walls, the range is
greatly reduced.
Doorbell beeps every ten minutes.
The battery is low in the doorbell. Replace with AA Alkaline
batteries.
Need to clear doorbell’s memory.
Press and hold Learn button, an initial beep will be heard.
Continue to hold until a second beep is heard (about 6 seconds).
Once memory is clear the doorbell can be programmed to a new
network.
Intercom can not be programmed to network.
A network may contain up to 12 intercoms. It may be necessary
to clear the network and reprogram all the intercoms to the
network. See Programming Intercom.
The intercom does not connect to another intercom and a
green light is on longer than 3-1/2 minutes.
The intercom is out of range. Place the intercom closer to the
other intercoms in the network, with the antenna pointing up.
The other intercom in the network has no power. Replace the
batteries. The intercom has not completed programming. Clear
the intercom's memory and reprogram.
The intercom VOX mode is not working.
The intercom will take about 40 seconds to reactivate after
responding to a doorbell call.
NOTE: Manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this
equipment. Changes or modifications not expressly approved
by the manufacturer could void the authority to operate the
equipment.
ONE YEAR LIMITED WARRANTY