Black & Decker Cordless Sander BDCMTO User Manual

0

Out of 0 Ratings

Owner's of the Black & Decker Cordless Sander BDCMTO gave it a score of 0 out of 5. Here's how the scores stacked up:

  • Reliability

    0 out of 5

  • Durability

    0 out of 5

  • Maintenance

    0 out of 5

  • Performance

    0 out of 5

  • Ease of Use

    0 out of 5
of 28
 
6
WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses. Also use
face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT.
WARNING: CUT HAZARD. Before cutting any type of material, be sure it is firmly anchored
or clamped to prevent slipping.
WARNING: CUT HAZARD. Let the tool work at its own pace. Do not overload, blade
breakage may occur.
WARNING: CUT HAZARD. This tool has no provision to lock the switch in the ON position,
and should never be locked in the ON position by any other means.
To make a cut:
•Clearlymarkthedesiredcuttingarea.
•Toswitchthetoolon,pullthevariablespeedtriggeronthepower
unit. The tool speed depends on how far you pull the trigger.
•Switchthetoolonbeforeapplyingpressureandslowlyfeedthe
plunge cut blade into the workpiece at the marked location.
WARNING: CUT HAZARD. Ensure the blade is not in contact
with cutting surface before starting saw.
•Advancethebladealongthecuttinglineuntilcutiscompleted.
Don’t force the tool; let the blade cut at its own speed.
•Toswitchthetooloff,releasethetrigger.
NOTE: Always use the appropriate type of saw blade for the work piece material and type of cut.
Cut only with sharp blades; they cut cleaner, faster and put less strain on the motor while cutting.
SANDING
WARNING: Fire hazard. When working on metal surfaces, do not use a vacuum cleaner
because sparks are generated. Wear safety glasses and a dustmask. Due to the danger of fire, do not
use your sander to sand magnesium surfaces. Do not use for wet sanding.
• Toswitchthetoolon,pullthevariablespeedtriggeronthepowerunit.Thetoolspeeddependson
how far you pull the trigger.
• Toswitchthetooloff,releasethetrigger.
NOTE: Do not rest fingers on platen during use. Move it in long sweeping strokes across the
surface, letting it do the work. Light pressure is all that is required for sanding. Excessive pressure
will slow the tool and produce inferior results. Check your work often, product is capable of removing
material rapidly. Excessive force will reduce the working efficiency and cause motor overload.
Replacing the sanding sheet regularly will maintain optimum working efficiency.
NOTE: Always ensure the workpiece is firmly held or clamped to prevent movement. Any movement
of the material may affect the quality of the sanding finish.
INSTALLING/REMOVING SANDING SHEETS - FIGURE D
A diamond shaped platen uses a hook and loop adhesion system to
attach the sanding sheets. The platen allows you to use it on large flat
surfaces and tight spots or corners.
•Attachthesandingplatenasdescribedunder“Installing/Removing
Accessories.”
•Aligntheedgesonthesandingsheet,withtheedgeofthesanding
platen and press the sanding sheet onto the platen.
•Firmlypressthebasewiththesandingsheetattachedagainsta
flat surface and briefly switch the tool on. This provides for good
adhesion between the platen and the sanding sheet, and also helps
to prevent premature wear.
•Whenthetipofthesandingsheetbecomesworn,detachthesheetfrom
the platen, rotate and reapply.
D
C

   Find Your Products By Category